Falsing Totally Explained

Everything about Falsing totally explained

In telecommunications, falsing describes a decoder detecting a valid input when one isn't present. This is also known as a false decode. To make the concepts simpler, this article will discuss analog circuits used before digital signal processing. Examples of decoder falsing include:

a telephone answering machine detecting dial pulses from a rotary dial as ringing voltage. The result being that the answering machine answers in response to dialing.
a two-way radio with an enabled CTCSS decoder turns on the receive audio for one or two syllables of a signal with a close-in-tone-frequency, (but wrong), CTCSS tone. The person listening to the radio occasionally hears nonsense partial words from the receiver's speaker: "et"... "up"...
a ringy telephone circuit with SF single-frequency signaling and poor level discipline drops calls because it sees harmonic frequencies or the distorted waveform as a valid "circuit idle" or "on-hook" SF signal.
power line transients cause a telemetry decoder to momentarily decode the power line noise as a false "turn-on" command, causing a remote-controlled water well pump to cycle on and off needlessly.

Analog tone decoders used in telephone and two-way radio systems are designed to work in a balance between expensive, complicated filtering and low cost simplicity. The engineering problem is to make the simplest circuit that will work reliably. A decoder generally tries to filter an audio input in order to strip off every audio component except a sought-after, specific tone. In part, a decoder is a narrow bandpass filter. A signal that gets through the narrow filter is rectified into a DC voltage which is used to switch something on or off.
Falsing sometimes occurs on a voice circuit when a human voice hits the exact pitch to which the tone decoder is tuned, a condition known as talk-off.
In order for the tone decoder to work reliably, the audio input level must be in the linear range of audio stages, (undistorted). A 1,500 Hz tone fed into an amplifier that distorts the tone could produce a harmonic at 3,000 Hz, falsely triggering a decoder that's tuned to 3,000 Hz.

Reducing the possibility of falsing

In some systems where tone signaling is used, higher reliability and less probability of falsing is needed. One method of reducing falsing is to use formats with simultaneous, paired tones. In decoding dual tones such as ICAO's SelCall, Quik Call I, MF, or DTMF, pairs of decoders are used and their outputs are connected to logical and cicuitry. When tones are decoded, they're submitted to the and logic. If both are decoded at the same time, the and logic output shows a decoded pair of tones is present. In order to false in a dual-tone system, both decoders would have to false at the same moment. Two-out-of-five code and similar methods provide an additional check in some applications.
Another method is to subject tone decoding to a time constraint. In the case of Quik Call I or a string of DTMF digits, the falsing would have to occur in the exact order required to actuate the decoder. This is much more improbable than falsing in a single tone decoder. In two-tone sequential, tone and voice radio paging, decoders are actuated by decoding one tone and then a second in the proper sequence. Falsing could only occur if the two decoders falsed in a valid sequence within the decoder's time constraints. Examples of systems of two-tone sequential paging are Motorola Quik Call II, General Electric Mobile Radio Type 99, and later-model Plectron receivers.

Further Information

Get more info on 'Falsing'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://falsing.totallyexplained.com">Falsing Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.